{"title":"Rock Slider","description":"\u003cp\u003eHeavy duty kickout rock sliders built from 2x2 inch square tubing with CNC-bent frame mounting brackets. Bolt-on installation using factory frame holes — no drilling or welding on your truck — shipped as DIY weld-together kits.\u003c\/p\u003e","products":[{"product_id":"4th-gen-dodge-ram-1500-kickout-rock-slider-weld-together-kit-bolt-on","title":"4th Gen Dodge Ram 1500 Kickout Rock Slider Weld-Together Kit","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 4th generation (2009-2018) Dodge Ram 1500 and 2019+ Ram 1500 Classic. While the sliders themselves are a weld-together kit, absolutely no welding, drilling or cutting of the actual vehicle is required! We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders mount directly to your Ram 1500's frame using C-shaped 1\/4\" thick steel mounting plates that wrap around the outer, bottom and inner walls of the truck's main frame rail. We finish these off with heavy gauge square tubing inner legs and the largest reinforcing gussets that we could fit under there.\u003cbr\u003eThese aren’t your average round tube sliders. The inner rails and mounting legs are made from 2×2″ heavy wall square tubing and finished with large 1\/4″ thick CNC-cut and bent frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the C-shaped frame mounting brackets in-house, with each bracket custom tailored to the Ram’s frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Ram’s frame. No frame drilling, welding or modification required. Our C-shaped frame mounting brackets wrap around the outer, bottom and inner faces of the frame, and then we run bolts through the outer and inner walls of the frame and into nuts that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the 1\/2″ to 5\/8″ diameter bolts and deform the 1\/4″ thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that large impacts will get spread out over a large area of your truck’s frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle’s frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. On the 4th gen Ram, the relationship between the frame rails and the rocker panels means the sliders must be dropped down from the frame slightly which can complicate installation. The 6 (3 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 5 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed.\u003c\/p\u003e\u003cp\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together – everything you need for assembly and installation included\u003c\/p\u003e\u003cp\u003e• NO Drilling, cutting or welding of the actual vehicle required – these sliders can be removed from your Dodge Ram without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams – the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e• 96″ Length provides full wheel well to wheel well protection\u003c\/p\u003e\u003cp\u003e• 2 x 2″ – 3\/16″ wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e• C-shaped 1\/4″ thick frame mounting brackets and gussets distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e• Includes brackets and detailed instructions to adjust the position of the factory parking brake cable, which Dodge placed directly in the way of rock sliders on the driver’s side!\u003c\/p\u003e\u003cp\u003e• Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264233820444,"sku":"CO94998","price":947.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_d94b76a8-faca-4889-968f-480e8c6f1756.jpg?v=1783517151"},{"product_id":"6th-gen-ford-bronco-rock-slider-weld-together-kit-bolt-on","title":"6th Gen Ford Bronco Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThese aren't your average round tube sliders. The main rails are made from 2x2\" heavy wall square tubing and finished with CNC-formed 1\/4\" steel mounting brackets and legs that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the frame mounting brackets in-house, with each bracket custom tailored to the Bronco's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Frontier's frame. No frame drilling, welding or modification required. Our C-shaped frame mounting brackets wrap around the outer, bottom and inner faces of the frame, and then we run bolts through the outer and inner walls of the frame and into nuts that get secured on the backside. This means that in order for these rock slider mounts to fail, you would have to simultaneously snap the heads off the bolts and deform the 1\/4\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The CNC-formed mounting legs bridge the gap between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions. As a finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 6 (3 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cp\u003e\u003cb\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/b\u003e\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your Ford Bronco without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e•Only Fits 4-door models at this time\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access the cabin or a roof rack\u003c\/p\u003e\u003cp\u003e•73\" length options provide full wheel well to wheel well protection while still allowing clearance for oversized tires\u003c\/p\u003e\u003cp\u003e• 2 x 2\" - 0.1875\"  wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e•C-shaped 1\/4\" thick frame mounting brackets and legs are CNC-bent in house. These maximize ground clearance below the pinch weld and distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264236540188,"sku":"CO12827","price":740.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_3da90f50-5c41-4fc0-b17b-2f0c5c3edf56.jpg?v=1783516549"},{"product_id":"2nd-gen-1993-2011-ford-ranger-kickout-rock-slider-weld-together-kit","title":"2nd\/3rd Gen 1993-2011 Ford Ranger Kickout Rock Slider Weld-Together Kit","description":"\u003cp\u003eThese aren't your average round tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from 2x2\" wall square tubing and finished with large CNC-cut frame mounting plates and rear gussets that ensure these sliders will stand up to the harshest abuse you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your Ranger frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates get welded onto your Ranger's frame and spread impact loads evenly over your frame rails. 2x2\" 3\/16\" wall square tube legs bridge the gap between the mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions. As a finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent, pre-cut and ready to weld. The kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 6 (3 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the right angle and distance from the Ranger without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cp\u003e\u003cspan style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eThis is a weld-on rock slider kit that requires welding to your vehicle's frame. When ordering this product, please ensure that it complies with the local regulations in your jurisdiction. \u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-weight: bolder;\"\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e•Weld-on design includes mounting plates sized specifically for your 2nd gen Ranger's frame\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e•Fits regular cab, extended cab and stepside 2nd\/3rd gen Rangers from 1993-2011\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access the cabin or a roof rack\u003c\/p\u003e\u003cp\u003e•78\" length ( provide full wheel well to wheel well protection while still allowing clearance for oversized tires\u003c\/p\u003e\u003cp\u003e• 2 x 2\" - 0.1875\"  wall square tubing inner rails and mounting legs are extremely heavy duty compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264237588764,"sku":"CO13066","price":697.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_14ecf8d6-e0c6-4dc4-b2e5-45d5f4b0aef4.jpg?v=1783517150"},{"product_id":"2019-ford-ranger-kickout-rock-slider-weld-together-kit-bolt-on","title":"2019-2021 Ford Ranger Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 2019+ Ford Ranger. While the sliders themselves are a weld-together kit, absolutely no welding, drilling or cutting of the actual vehicle is required! While the sliders themselves are a weld-together kit, absolutely no welding, drilling or cutting of the actual vehicle is required! We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders mount directly to your Ranger's frame using large 3\/8\" thick steel mounting plates as well as square tubing inner rails and the largest reinforcing gussets that we could fit under there.\u003c\/p\u003e\u003cp\u003eThese aren't your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from 2x2\" wall square tubing and finished with massive 3\/8\" thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through them under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails by sandwiching the frame rails between front and back 3\/8\" thick pads with 1\/2\" Bolts. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump. \u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 15 degree angle to provide a happy medium. \u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eNO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your Ranger without a trace that they were ever installed. \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eDetailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e84.5\" Length provides full wheel well to wheel well protection \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e2x2 1\/8\" wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eMassive 3\/8\" thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHilift jack can be used anywhere along the slider length to lift the vehicle \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e45 degree tapered inner rails to glance off obstacles \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eSold in pairs\u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264237752604,"sku":"CO70012","price":818.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_a6a8b047-dbe5-4378-88be-811022f482b2.jpg?v=1783517150"},{"product_id":"2003-2023-lexus-gx-land-cruiser-prado-kickout-rock-slider-weld-together-kit-bolt-on","title":"2003-2023 Lexus GX \/ Land Cruiser Prado Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThese aren't your average round tube sliders. The inner rails and mounting legs are made from 2x2\" heavy wall square tubing and finished with large 3\/16\" thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We laser cut the frame mounting brackets in-house, with each bracket custom tailored to the Lexus GX \/ Toyota Prado passenger and driver side frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Lexus GX \/ Toyota Prado frame. No frame drilling, welding or modification is required (Although 2 additional optional holes are pre-cut into the passenger side mounting plate for hard offroad use). Our frame mounting brackets wrap around the outer and bottom faces of the frame, and then we run bolts through the frame and into nuts that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the bolts and deform the 3\/16\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your vehicle's frame. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by tons of diagrams and pictures. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•NO Drilling, cutting or welding of the actual vehicle required - these bolt-on sliders can be removed from your GX\/ Prado without a trace that they were ever installed (2 additional optional holes are pre-cut into the passenger side mounting plate for hard offroad use)\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Detailed instructions and diagrams - the step by step directions and many diagrams make these a perfect first welding project\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•Fits Lexus GX470, Lexus GX460, Toyota Prado 120 and Toyota Prado 150 Models from 2003-2023\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•Fits KDSS-equipped models and includes clear instructions for accommodating the KDSS components\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access your roof rack or open your roof top tent\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•68\"  slider length provide full wheel well to wheel well protection\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• 2x2 3\/16\" wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Massive 3\/16\" thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent frame damage\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Sold in pairs\u003c\/span\u003e\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264240079132,"sku":"CO12778","price":814.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_05e5702a-0bb2-4bc3-9879-00a84acf9895.jpg?v=1783515617"},{"product_id":"6th-gen-hilux-kickout-rock-slider-weld-together-kit-bolt-on","title":"6th Gen Hilux Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThese aren't your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from heavy wall 1.5\" (40mm) and 2\" (50mm) square tubing and finished with massive 3\/8\" thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We fabricate the frame mounting brackets in-house, with each bracket custom tailored to the 6th Gen Hilux's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Toyota Hilux's frame. No frame drilling, welding or modification required. With this kit, the provided frame plates spread impact loads evenly over your frame rails by sandwiching the frame rails between front and back 3\/8\" (10mm) thick pads with 1\/2\" (M12) Bolts. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the 1\/2\" (M12) diameter bolts and deform the 3\/8\" (10mm) thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e•NO cutting or welding of the actual vehicle required - these sliders can be removed from your 6th Gen (1997-2004) Toyota Hilux without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e•Fits extended cab and 4 door Models\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•71\" Length provides full wheel well to wheel well protection\u003c\/p\u003e\u003cp\u003e• 1.5x1.5\" 3\/16\" (40x40 5mm ) and 2x2\" 1\/8\" (50x50 3mm) wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e• Massive 3\/8\" (10mm) thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264240537884,"sku":"CO107371","price":814.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_bce3389a-79a4-402f-be67-b4d2354c7fd2.jpg?v=1783515135"},{"product_id":"7th-gen-hilux-kickout-rock-slider-weld-together-kit-bolt-on","title":"7th Gen Hilux Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThese aren't your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from heavy wall 1.5\" (40mm) and 2\" (50mm) square tubing and finished with massive 3\/8\" thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We fabricate the frame mounting brackets in-house, with each bracket custom tailored to the 7th Gen Hilux's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Toyota Hilux frame. No frame drilling, welding or modification required. With this kit, the provided frame plates spread impact loads evenly over your frame rails by sandwiching the frame rails between front and back 3\/8\" (10mm) thick pads with 1\/2\" (M12) Bolts. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the 1\/2\" (M12) diameter bolts and deform the 3\/8\" (10mm) thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e•NO cutting or welding of the actual vehicle required - these sliders can be removed from your 7th Gen (2005-2015) Toyota Hilux without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e•Fits extended cab and 4 door Models\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•75\" Length provides full wheel well to wheel well protection without interfering with the way that the 7th gen hilux body dips down slightly near each wheel well.\u003c\/p\u003e\u003cp\u003e• 1.5x1.5\" 3\/16\" (40x40 5mm ) and 2x2\" 1\/8\" (50x50 3mm) wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e• Massive 3\/8\" (10mm) thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264240603420,"sku":"CO107404","price":839.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_b809801f-32fb-4a6f-87b6-8ca40519b0e4.jpg?v=1783515136"},{"product_id":"80-series-land-cruiser-kickout-rock-slider-weld-together-kit-bolt-on","title":"80 Series Land Cruiser Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThese aren't your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from heavy wall 1.5\" (40mm) and 2\" (50mm) square tubing and finished with massive 3\/8\" thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We fabricate the frame mounting brackets in-house, with each bracket custom tailored to the 80 Series Cruiser's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the 80 Series' frame. No frame drilling, welding or modification required. With this kit, the provided frame plates spread impact loads evenly over your frame rails by sandwiching the frame rails between front and back 3\/8\" (10mm) thick pads with 1\/2\" (M12) Bolts. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the 1\/2\" (M12) diameter bolts and deform the 3\/8\" (10mm) thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/p\u003e\u003cp\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/p\u003e\u003cp\u003e•IMPORTANT NOTE: For the early 80 Series models that have the factory exhaust components routed on the outside of the right hand side frame rail, you will need to relocate these exhaust components or modify the slider leg in this location.\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your 80 Series Land Cruiser\/ Lexus LX450 without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•68\" Length (4 door) provides full wheel well to wheel well protection\u003c\/p\u003e\u003cp\u003e• 1.5x1.5\" 3\/16\" (40x40 5mm ) and 2x2\" 1\/8\" (50x50 3mm) wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e• Massive 3\/8\" (10mm) thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264241226012,"sku":"CO107423","price":814.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_a8405ff3-af51-437a-9397-572415d0b1ee.jpg?v=1783515136"},{"product_id":"90-series-land-cruiser-rock-slider-weld-together-kit-bolt-on","title":"90 Series Land Cruiser Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 90 Series Toyota Land Cruiser Prado. While the sliders themselves are a weld-together kit, absolutely no welding, drilling or cutting of the actual vehicle is required! We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders mount directly to your 90 Series Cruiser's frame using large 3\/8\" (10mm) thick steel mounting plates as well as square tubing inner rails and the largest reinforcing gussets that we could fit under there.\u003c\/p\u003e\u003cp\u003eThese aren’t your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from thick wall 1.5″ (40mm) and 2″ (50mm) square tubing and finished with massive 3\/8″ thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We fabricate the frame mounting brackets in-house, with each bracket custom tailored to the 90 Series Cruiser’s frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the 90 Series’ frame. No frame drilling, welding or modification required. With this kit, the provided frame plates spread impact loads evenly over your frame rails by sandwiching the frame rails between front and back 3\/8″ (10mm) thick pads with 1\/2″ (M12) Bolts. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the 1\/2″ (M12) diameter bolts and deform the 3\/8″ (10mm) thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck’s frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle’s frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/p\u003e\u003cp\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together – everything you need for assembly and installation included\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required – these sliders can be removed from your 90 Series Land Cruiser Prado without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams – the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•65″ Length (4 door) provides full wheel well to wheel well protection\u003c\/p\u003e\u003cp\u003e• 1.5×1.5″ 1\/4″ wall (40×40 x 6mm ) and 2×2″ 3\/16″ wall (50×50 x 5mm) square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e• Massive 3\/8″ (10mm) thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264241291548,"sku":"CO12795","price":750.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_160f061f-e1e2-4303-ba95-9637807f6470.jpg?v=1783516547"},{"product_id":"100-series-land-cruiser-rock-slider-weld-together-kit-bolt-on","title":"100 Series Land Cruiser Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 100 Series Toyota Land Cruiser and Lexus LX470. While the sliders themselves are a weld-together kit, absolutely no welding, drilling or cutting of the actual vehicle is required! We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders mount directly to your 100 Series Cruiser's frame using large 3\/8\" (10mm) thick steel mounting plates as well as square tubing inner rails and the largest reinforcing gussets that we could fit under there.\u003c\/p\u003e\u003cp\u003eThese aren’t your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from 3\/16″ (5mm) thick wall 2″ (50mm) square tubing and finished with massive 3\/8″ thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We fabricate the frame mounting brackets in-house, with each bracket custom tailored to the 100 Series Cruiser \/ Lexus LX470 frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the 100 Series frame. No frame drilling, welding or modification required. With this kit, the provided frame plates spread impact loads evenly over your frame rails by sandwiching the frame rails between front and back 3\/8″ (10mm) thick pads with 1\/2″ (M12) Bolts. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the 1\/2″ (M12) diameter bolts and deform the 3\/8″ (10mm) thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck’s frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle’s frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/p\u003e\u003cp\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together – everything you need for assembly and installation included\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required – these sliders can be removed from your 100 Series Land Cruiser \/ Lexus LX470 without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams – the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•71″ Length provides full wheel well to wheel well protection\u003c\/p\u003e\u003cp\u003e• 2×2″ 3\/16″ wall (50×50 x 5mm) square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e• Massive 3\/8″ (10mm) thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264241455388,"sku":"CO12796","price":749.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_f1d07180-5dee-411a-9a14-57b9c21280e3.jpg?v=1783516547"},{"product_id":"2005-2023-toyota-tacoma-kickout-rock-slider-weld-together-kit-bolt-on","title":"2005-2023 Toyota Tacoma Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThese aren't your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from heavy wall 2x2\" (50x50mm) square tubing and finished with massive 3\/8\" thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We fabricate the frame mounting brackets in-house, with each bracket custom tailored to the tacoma's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the tacoma's frame. No frame drilling, welding or modification required. With this kit, the provided frame plates spread impact loads evenly over your frame rails by sandwiching the frame rails between front and back 3\/8\" thick pads with 1\/2\" Bolts. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the 1\/2\" diameter bolts and deform the 3\/8\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/p\u003e\u003cp\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your tacoma without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e•Fits 4 Door and Extended Cab Models\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•84.5\" Length provides full wheel well to wheel well protection\u003c\/p\u003e\u003cp\u003e• 2x2 1\/8\" wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e• Massive 3\/8\" thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264241783068,"sku":"CO119035","price":860.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_c6fc8713-d5be-4330-8a71-09132b9cb8ad.jpg?v=1783515611"},{"product_id":"1st-gen-tundra-kickout-rock-slider-weld-together-kit-bolt-on","title":"1st Gen Tundra Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 1st generation (1999-2006) Toyota Tundra. While the sliders themselves are a weld-together kit, absolutely no welding or modification of the actual vehicle is required, other than the optional drilling of 2 extra holes that are provided for heavy offroad use. We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders bolt directly to your Toyota Tundra's frame using L-shaped 1\/4\" thick steel mounting plates that wrap around the outer and bottom walls of the truck's main frame rail. We finish these off with heavy gauge square tubing inner legs and the largest reinforcing gussets that we could fit under there.\u003c\/p\u003e\u003cp\u003eThese aren’t your average round tube sliders. The inner rails and mounting legs are made from 2×2″ heavy wall square tubing and finished with large 1\/4″ thick CNC-cut and bent frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the frame mounting brackets in-house, with each bracket custom tailored to the 1st Generation Tundra’s frame profile at each mounting point. This allows us to mount these sliders to the truck using factory holes in the Tundra’s frame. No frame welding or modification is required other than the optional drilling of 2 extra holes that are provided for heavy offroad use. Our L-shaped frame mounting brackets wrap around the outer and bottom faces of the frame, and then we run bolts through the walls of the frame and into the supplied nut plates that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the bolts and deform the 1\/4″ thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck’s frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle’s frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 8 (4 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cp\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together – everything you need for assembly and installation included\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required – these sliders can be removed from your Toyota Tundra without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams – the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e•Fits Double Cab, Access Cab and Regular Cab Tundra Models from 1999-2006 (1st generation)\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•84″ and 96″ length options provide full wheel well to wheel well protection for all 1st gen Tundra models\u003c\/p\u003e\u003cp\u003e• 2 x 2″ heavy wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e•C-shaped 1\/4″ thick frame mounting brackets and gussets are CNC-bent in house. These distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264242798876,"sku":"CO12789","price":860.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_5aee425c-cfe2-4f6b-ae32-63b5ff880078.jpg?v=1783515615"},{"product_id":"2007-2021-toyota-tundra-kickout-rock-slider-weld-together-kit-bolt-on","title":"2007-2021 Toyota Tundra Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eHere is our 2007-2021 Toyota Tundra Kickout Rock Slider DIY Kit, made to fit Gen 2 (2007-2013) and Gen 2.5 (2014-2021) Tundras. These aren't your average round tube sliders. The main rails are made from 2x2\" heavy wall square tubing and finished with CNC-formed 1\/4\" steel mounting brackets and legs that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the frame mounting brackets in-house, with each bracket custom tailored to the 2nd Gen Tundra frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Tundra's frame. No frame drilling, welding or modification required. Our C-shaped frame mounting brackets wrap around the outer, bottom and inner faces of the frame, and then we run bolts through the outer and inner walls of the frame and into nuts that get secured on the backside. This means that in order for these rock slider mounts to fail, you would have to simultaneously snap the heads off the bolts and deform the 1\/4\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eBesides the aforementioned features, what really makes these rock sliders unique is the rear mounting point, which wraps around the factory leaf spring mount and also provides you with a frame-mounted tie down point for a camper. This rather complicated looking bracket is designed and manufactured in-house to attach to the factory leaf spring bolt and surrounding frame holes to give theses sliders a frame mounting point located right in front of the rear tires. This is in contrast to our competitors' rock sliders, which place all of their frame mounting points under the cab, leaving a huge unsupported length of rock slider under the bed. This unsupported length can flex into your bed under hard hits, damaging your vehicle and negating the reason you installed rock sliders in the first place! The second benefit of our leaf spring mount is the ability to tie down a slide-in camper. Slide-in campers are great for going offroad, but they often require you to run vulnerable tie down bars which hang below your vehicle and can easily get bent or damaged while offroad. With our rock sliders, we've placed a camper tie down point inside the kickout, giving you all the vehicle protection of a dedicated rock slider while also keeping your tie down point out of harms way. This also saves you the cost and hassle of purchasing stand alone camper tie down bars to fit your Tundra.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The CNC-formed mounting legs bridge the gap between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions. As a finishing touch, the rear ends of the square main rails are tapered with a very long angled cut to maximize protection and ground clearance where the Tundra bedside dips down lower than the rest of the rock panel. \u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 8 (4 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eImportant Note: You may have noticed that this rock slider kit is a little bit pricier than our rock sliders for other makes and models. This is due to our proprietary leaf spring mounting bracket and camper tie down point, which add several complex parts to each kit. However, we feel that the unmatched strength and functionality that these features provide are well worth that bit of extra complexity and cost. \u003c\/b\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-weight: bolder;\"\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your Toyota Tundra without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e•Multiple body style options provide customized wheel well to wheel well protection for each model while still allowing clearance for oversized tires. (We do not support the 4 door 8 foot bed model at this time, sorry!)\u003c\/p\u003e\u003cp\u003e•Integrated camper tie down point is located inside the kickout, allowing you to attach your slide-in camper tie downs directly to our rock sliders. \u003c\/p\u003e\u003cp\u003e•Unique Leaf Spring Mounting Point completely eliminates the rear overhang, giving unmatched impact strength and support for the integrated camper tie down point. \u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access the cabin or a roof rack\u003c\/p\u003e\u003cp\u003e• 2 x 2\" - 0.1875\"  wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e•C-shaped 1\/4\" thick frame mounting brackets and legs are CNC-bent in house. These maximize ground clearance below the pinch weld and distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e•Tapered inner rails to glance off obstacles and maximize ground clearance and protection under the Tundra's bed.\u003c\/p\u003e\u003cp\u003e• Sold as a left and right pair\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264243061020,"sku":"CO12840","price":997.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_7adaf5f5-613e-448a-8511-250a8cd0e423.jpg?v=1783516550"},{"product_id":"3rd-gen-toyota-4runner-hilux-surf-kickout-rock-slider-weld-together-kit-bolt-on","title":"3rd Gen Toyota 4Runner \/ Hilux Surf Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eThis is a DIY weld-together rock slider kit for the 3rd generation (1996-2002) Toyota 4Runner and Hilux Surf. While the sliders themselves are a weld-together kit, absolutely no welding or modification of the actual vehicle is required, other than the optional drilling of some extra holes that are provided for heavy offroad use. We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders bolt directly to your Toyota 4Runner frame using 1\/4\" thick steel mounting plates that wrap around the outer and bottom walls of the truck's main frame rail. We finish these off with heavy duty 1\/4\" wall square tubing inner legs and the largest reinforcing gussets that we could fit under there.\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eThese aren’t your average round tube sliders. The inner rails and mounting legs are made from thick 1\/4\" wall square tubing and finished with large 1\/4″ thick CNC-cut and bent frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the frame mounting brackets in-house, with each bracket custom tailored to the 3rd Generation 4Runner's frame profile at each mounting point. This allows us to mount these sliders to the truck using factory holes in the 4Runner's frame. No frame welding or modification is required other than the optional drilling of a few extra holes that are provided for heavy offroad use. Our  frame mounting brackets wrap around the outer and bottom faces of the frame, and then we run bolts through the walls of the frame and into the supplied nut plates that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the bolts and deform the 1\/4″ thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck’s frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle’s frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 6 (3 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together – everything you need for assembly and installation included\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e•NO cutting or welding of the actual vehicle required – these sliders can be removed from your Toyota 4Runner without a trace that they were ever installed.\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e• Detailed instructions and diagrams – the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e•Fits all 3rd gen 4Runner and Hilux Surf models from 1996-2002\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e•65\" length provide full wheel well to wheel well protection for your 3rd gen 4Runner\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e• heavy wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders - we are confident you will never bend these sliders even under the hardest of hits! \u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e•1\/4″ thick frame mounting brackets and gussets are CNC-bent in house. These distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264244044060,"sku":"CO12974","price":741.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_045fd0f7-cc0f-4954-ae6f-a92d5a9a2b79.jpg?v=1783516718"},{"product_id":"2003-2023-toyota-4runner-hilux-surf-kickout-rock-slider-weld-together-kit-bolt-on","title":"2003-2023 Toyota 4Runner \/ Hilux Surf Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThese aren't your average round tube sliders. The inner rails and mounting legs are made from 2x2\" heavy wall square tubing and finished with large 3\/16\" thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We laser cut the frame mounting brackets in-house, with each bracket custom tailored to the 4Runner's passenger and driver side frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the 4Runner's frame. No frame drilling, welding or modification is required (Although 2 additional optional holes are pre-cut into the passenger side mounting plate for hard offroad use). Our frame mounting brackets wrap around the outer and bottom faces of the frame, and then we run bolts through the frame and into nuts that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the bolts and deform the 3\/16\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by tons of diagrams and pictures. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•NO Drilling, cutting or welding of the actual vehicle required - these bolt-on sliders can be removed from your 4Runner without a trace that they were ever installed (2 additional optional holes are pre-cut into the passenger side mounting plate for hard offroad use)\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Detailed instructions and diagrams - the step by step directions and many diagrams make these a perfect first welding project\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•Fits Toyota 4Runner Models from 2003-2023 (4th and 5th generation)\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•Fits KDSS-equipped models and includes clear instructions for accommodating the KDSS components\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access your roof rack or open your roof top tent\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•68\"  slider length provide full wheel well to wheel well protection\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• 2x2 3\/16\" wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Massive 3\/16\" thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent frame damage\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Sold in pairs\u003c\/span\u003e\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264244371740,"sku":"CO12777","price":814.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_32dc0ba4-56e2-456e-b826-ae00f4184600.jpg?v=1783515613"},{"product_id":"2nd-gen-frontier-kickout-rock-slider-weld-together-kit-bolt-on","title":"2nd Gen Frontier Kickout Rock Slider Weld-Together Kit (Bolt-on)","description":"\u003cp\u003eThese aren't your average round tube sliders. The inner rails and mounting legs are made from 2x2\" heavy wall square tubing and finished with large 1\/4\" thick CNC-cut and bent frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the frame mounting brackets in-house, with each bracket custom tailored to the Frontier's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Frontier's frame. No frame drilling, welding or modification required. Our C-shaped frame mounting brackets wrap around the outer, bottom and inner faces of the frame, and then we run bolts through the outer and inner walls of the frame and into nuts that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the bolts and deform the 1\/4\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 6 (3 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cp\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your Nissan Frontier without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e•Fits 4 Door and Extended Cab Models\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•84\" Length provides full wheel well to wheel well protection\u003c\/p\u003e\u003cp\u003e• 2 x 2\" heavy wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e•C-shaped 1\/4\" thick frame mounting brackets and gussets are CNC-bent in house. These distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264244928796,"sku":"CO119814","price":860.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_c961a2e9-7e84-46d7-b7a5-4153f2e58eae.jpg?v=1783515611"},{"product_id":"3rd-generation-2022-nissan-frontier-kickout-rock-slider-weld-together-kit-bolt-on","title":"3rd Generation (2022+) Nissan Frontier Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 3rd generation (2022+) Nissan Frontier. While the sliders themselves are a weld-together kit, absolutely no welding, drilling or cutting of the actual vehicle is required! We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders mount directly to your Nissan Frontier's frame using C-shaped 1\/4\" thick steel mounting plates that wrap around the outer, bottom and inner walls of the truck's main frame rail. We finish these off with heavy gauge square tubing inner legs and the largest reinforcing gussets that we could fit under there.\u003c\/p\u003e\u003cp\u003eThese aren't your average round tube sliders. The inner rails and mounting legs are made from 2x2\" heavy wall square tubing and finished with large 1\/4\" thick CNC-cut and bent frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the frame mounting brackets in-house, with each bracket custom tailored to the Frontier's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Frontier's frame. No frame drilling, welding or modification required. Our C-shaped frame mounting brackets wrap around the outer, bottom and inner faces of the frame, and then we run bolts through the outer and inner walls of the frame and into nuts that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the bolts and deform the 1\/4\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that large impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 6 (3 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eNO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your Nissan Frontier without a trace that they were ever installed.\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eDetailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eFits 4 Door and Extended Cab Models\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e84\" Length provides full wheel well to wheel well protection\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e2 x 2\" heavy wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eC-shaped 1\/4\" thick frame mounting brackets and gussets are CNC-bent in house. These distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eSold in pairs\u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264245223708,"sku":"CO95001","price":860.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_2f6c1b41-5915-4b59-907e-e32fc7e70c73.jpg?v=1783514362"},{"product_id":"r51-nissan-pathfinder-kickout-rock-slider-weld-together-kit-bolt-on","title":"R51 Nissan Pathfinder Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003e***Updated R51 Pathfinder Photos Coming Soon! However, the style of the Sliders is the same as the 2022 Frontier Pictured \u003c\/p\u003e\u003cp\u003eThis is a DIY weld-together rock slider kit for the 2nd generation (2005-2012) R51 Nissan Pathfinder. While the sliders themselves are a weld-together kit, absolutely no welding, drilling or cutting of the actual vehicle is required! We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders mount directly to your Nissan R51 Pathfinder's frame using C-shaped 1\/4\" thick steel mounting plates that wrap around the outer, bottom and inner walls of the truck's main frame rail. We finish these off with heavy gauge square tubing inner legs and the largest reinforcing gussets that we could fit under there.\u003c\/p\u003e\u003cp\u003eThese aren't your average round tube sliders. The inner rails and mounting legs are made from 2x2\" heavy wall square tubing and finished with large 1\/4\" thick CNC-cut and bent frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the frame mounting brackets in-house, with each bracket custom tailored to the R51 Pathfinder's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the R51 Pathfinder frame. No frame drilling, welding or modification required. Our C-shaped frame mounting brackets wrap around the outer, bottom and inner faces of the frame, and then we run bolts through the outer and inner walls of the frame and into nuts that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the bolts and deform the 1\/4\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 6 (3 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your Nissan R51 Pathfinder without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•65\" Length provides full wheel well to wheel well protection for the R51 Pathfinder\u003c\/p\u003e\u003cp\u003e• 2 x 2\" heavy wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e•C-shaped 1\/4\" thick frame mounting brackets and gussets are CNC-bent in house. These distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264245453084,"sku":"CO119809","price":814.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_1bffa69d-b124-4a78-9087-3e8a1fba4484.jpg?v=1783515612"},{"product_id":"y60-nissan-patrol-kickout-rock-slider-weld-together-kit-bolt-on","title":"Y60 Nissan Patrol Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThese aren't your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from heavy wall 1.5\" (40mm) and 2\" (50mm) square tubing and finished with massive 3\/8\" thick CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We fabricate the frame mounting brackets in-house, with each bracket custom tailored to the GQ Patrol's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Patrol's frame. No frame drilling, welding or modification required. With this kit, the provided frame plates spread impact loads evenly over your frame rails by sandwiching the frame rails between front and back 3\/8\" (10mm) thick pads with 1\/2\" (M12) Bolts. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the 1\/2\" (M12) diameter bolts and deform the 3\/8\" (10mm) thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your truck's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 10 degree angle to provide a happy medium.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e\u003cbr\u003e\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•NO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your GQ Patrol without a trace that they were ever installed.\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•Specific Versions for 2 door and 4 door Models\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•71\" Length (4 door) provides full wheel well to wheel well protection\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• 1.5x1.5\" 3\/16\" (40x40 5mm ) and 2x2\" 1\/8\" (50x50 3mm) wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Massive 3\/8\" (10mm) thick frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• 45 degree tapered inner rails to glance off obstacles\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003e• Sold in pairs\u003c\/span\u003e\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264246239516,"sku":"CO107477","price":762.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_c3d2cf26-882b-49fd-b2c4-c0cb1b9f2890.jpg?v=1783515610"},{"product_id":"2nd-gen-nissan-xterra-kickout-rock-slider-weld-together-kit-bolt-on","title":"2nd Gen Nissan Xterra Kickout Rock Slider Weld-Together Kit (Bolt on)","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 2nd generation (2005-2015) Nissan Xterra. While the sliders themselves are a weld-together kit, absolutely no welding, drilling or cutting of the actual vehicle is required! We specifically designed these sliders to be a modification-free installation so they can be removed from the vehicle without leaving a trace that they were ever there. However, don't think for a second that this means the sliders aren't built for heavy offroad hits. These sliders mount directly to your Nissan Xterra's frame using C-shaped 1\/4\" thick steel mounting plates that wrap around the outer, bottom and inner walls of the truck's main frame rail. We finish these off with heavy gauge square tubing inner legs and the largest reinforcing gussets that we could fit under there.\u003c\/p\u003e\u003cp\u003eThese aren't your average round tube sliders. The inner rails and mounting legs are made from 2x2\" heavy wall square tubing and finished with large 1\/4\" thick CNC-cut and bent frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. We bend the frame mounting brackets in-house, with each bracket custom tailored to the Xterra's frame profile at each mounting point. This allows us to mount these sliders to the truck using all factory holes in the Xterra's frame. No frame drilling, welding or modification required. Our C-shaped frame mounting brackets wrap around the outer, bottom and inner faces of the frame, and then we run bolts through the outer and inner walls of the frame and into nuts that get secured on the backside. This means that in order for these rock sliders to fail, you would have to simultaneously snap the heads off the bolts and deform the 1\/4\" thick steel brackets enough to lift away from your frame! You can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThis mounting design also ensures that those big trail impacts will get spread out over a large area of your Xterra's frame. Some sliders use skimpy round tubing mounting legs that mount directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through the vehicle's frame under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle so that the rock sliders can be tucked closer to the xterra body to maximize ground clearance.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck.  To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by CAD diagrams. The 6 (3 per side) mounting legs in this kit ship pre-cut with the perfect angles and lengths so the sliders can be positioned at the perfect angle and distance from the vehicle without any guess work or frustrating angle cuts. The pictured sliders are set at a 10 degree angle to provide great ground clearance and a convenient step to reach your roof rack or truck bed. You can also adjust the angle up or down while assembling the sliders if you wish to have a flatter or more extreme slider angle.\u003c\/p\u003e\u003cp\u003e\u003cspan style=\"font-weight: bolder;\"\u003e• DIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/span\u003e\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the actual vehicle required - these sliders can be removed from your Nissan Xterra without a trace that they were ever installed.\u003c\/p\u003e\u003cp\u003e• Detailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003cp\u003e• CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and pickup bed\u003c\/p\u003e\u003cp\u003e•60\" Length provides great protection for the 2nd gen Xterra while allowing them to fit up into the \"divet\" in the rocker panels - this gets the rock slider up higher for additional ground clearance.\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails further help the rock sliders to be tucked up closer to the Xterra rocker panel for max ground clearance\u003c\/p\u003e\u003cp\u003e• 2 x 2\" heavy wall square tubing inner rails provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003cp\u003e•C-shaped 1\/4\" thick frame mounting brackets and gussets are CNC-bent in house. These distribute forces evenly into your vehicle frame to prevent damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e• 45 degree tapered inner rails allow the rock slider to be tucked up closer to the Xterra rocker panel for max ground clearance\u003c\/p\u003e\u003cp\u003e• Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264246698268,"sku":"CO13022","price":814.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_f66d9737-813d-4439-862d-bbdb3116fe88.jpg?v=1783516719"},{"product_id":"kickout-rock-slider-weld-together-kit","title":"Kickout Rock Slider Weld-Together Kit","description":"\u003cp\u003e    This is a DIY weld-together rock slider kit that is available in 65\", 68\" and 71\" lengths. The 65\" length fits the 1st-3rd gen 4Runner, 1st gen single cab Tacoma, FJ Cruiser, 1st-2nd gen Nissan Xterra and R50 Nissan Pathfinder. The 68\" length fits the 4th-5th gen 4Runner, 80-series Land Cruiser, Lexus GX470 and GX460, and Nissan R51 Pathfinder. The 71\" length fits the 100-series Land Cruiser, Lexus LX470 and Nissan Frontier.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eWhen placing your order, please enter your vehicle year and model into the notes section so we can verify fitment\u003c\/b\u003e\u003c\/p\u003e\u003cp\u003e    These aren't your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from 2x2\" wall square tubing and finished with massive CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. Some sliders use skimpy round tubing mounting legs that weld directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through them under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails and provide a huge amount of surface area to place your welds. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump. \u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck. Simply put, these sliders make for a perfect first-time welding project! To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 15 degree angle to provide a happy medium.\u003c\/p\u003e\u003cp\u003eThis is a weld-on rock slider kit that requires welding to your vehicle's frame. When ordering this product, please ensure that it complies with the local regulations in your jurisdiction. We do also have bolt-on rock slider kits for many vehicle makes and models and are continuing to expand our lineup of bolt-on rock sliders. Please search your vehicle model on our shop page for more details on if we have a bolt-on option for your vehicle.\" \u003c\/p\u003e\u003cp\u003e\u003cb\u003eWhen placing your order, please enter your vehicle year and model into the notes section so we can verify fitment \u003c\/b\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eDetailed instructions and diagrams - the step by step directions and diagrams make these a perfect first welding project \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and\/or pickup bed \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eMultiple length options ensure full wheel well to wheel well protection for your vehicle \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e2x2 1\/8\" wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eLarge frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHilift jack can be used anywhere along the slider length to lift the vehicle \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e45 degree tapered inner rails to glance off obstacles \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eSold in pairs\u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264247812380,"sku":"CO0575","price":697.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_e0c30ec8-b1fd-464c-bb74-15e0d1997e0a.jpg?v=1783514589"},{"product_id":"1st-gen-tacoma-kickout-rock-slider-weld-together-kit","title":"1st Gen Tacoma Kickout Rock Slider Weld-Together Kit","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 1st gen tacoma. These aren't generic round tube sliders that are prone to excessive flex and damaging the vehicle they are supposed to protect. The heavy duty square inner rails, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from 2x2\" square tubing and finished with massive CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them.\u003c\/p\u003e\u003cp\u003eSome sliders use skimpy round tubing mounting legs that weld directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through them under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails and provide a huge amount of surface area to place your welds. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump.\u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck. Simply put, these sliders make for a perfect first-time welding project! To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 8 (4 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eDetailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access the cabin, roof rack and\/or pickup bed\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e84\" Length provides wheel well to wheel well protection for your Xtra cab or Double cab Tacoma (for regular cab Tacomas, use our 65\" Kickout Rock slider kit: \u003ca href=\"https:\/\/www.coastaloffroad.com\/product-page\/65-weld-on-rock-slider-kit\/\"\u003ehttps:\/\/www.coastaloffroad.com\/product-page\/65-weld-on-rock-slider-kit\/\u003c\/a\u003e)\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e2x2 1\/8\" wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eMassive 3\/16\" steel frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent frame damage\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eSold in pairs\u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54289155653916,"sku":"CO74654","price":782.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_f828b6fe-37ca-4f1b-9201-6b02206bcd0e.jpg?v=1783585362"},{"product_id":"1st-gen-sequoia-kickout-rock-slider-weld-together-kit","title":"1st Gen Sequoia Kickout Rock Slider Weld-Together Kit","description":"\u003cp\u003eThis is a DIY weld-together rock slider kit for the 1st gen Toyota Sequoia. These aren't generic round tube sliders that are prone to excessive flex and damaging the vehicle they are supposed to protect. The heavy duty square inner rails, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from 2x2\" square tubing and finished with massive CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them.\u003c\/p\u003e\u003cp\u003eSome sliders use skimpy round tubing mounting legs that weld directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through them under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails and provide a huge amount of surface area to place your welds. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump. \u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck. Simply put, these sliders make for a perfect first-time welding project! To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. \u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eDetailed instructions and diagrams - the step by step directions and professionally made diagrams make these a perfect first welding project \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access the cabin and roof rack \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e75\" Length provides wheel well to wheel well protection for your Sequoia (The production sliders you will receive are longer than shown) \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e2x2 1\/8\" wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eMassive 3\/16\" steel frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent frame damage \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHilift jack can be used anywhere along the slider length to lift the vehicle \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e45 degree tapered inner rails to glance off obstacles \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eSold in pairs\u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54289155752220,"sku":"CO74658","price":828.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_9ca455f8-86c5-431b-befc-6db3f8a124f2.jpg?v=1783585384"},{"product_id":"2019-toyota-rav4-bolt-on-rock-sliders","title":"2019+ Toyota Rav4 Bolt-On Rock Sliders","description":"\u003cp\u003e This is a true offroad rock slider set for the 2019+ Toyota Rav4. Unlike most of our products which are DIY kits, these rock sliders ship to you already welded and powder coated - simply bolt them onto your Rav4 using the provided hardware. These rock sliders mount using existing factory mounting points (no drilling required) and provide excellent protection of your doors and rocker panels.  They are built to take a beating and can support the entire weight of the Rav4 with ease.  Due to the Rav4's unibody construction, the design of the mounting system is especially critical. If a strong rock slider is poorly mounted to the vehicle unibody, no matter how strong the rock slider is, it will simply punch through the unibody mounting points should a hard impact occur. Our mounting system uses a total of 10 bolts per rock slider to spread impact forces evenly throughout the entire length of the rocker panel structure. This substantially stiffens the rock sliders and protects the mounting interfaces on your Rav4's unibody. \u003c\/p\u003e\u003cp\u003eThe inner rails are CNC-cut and formed in-house at our Vancouver production facility. Made of 3\/16\" steel, these provide a solid foundation for the rest of the rock sliders. Each inner rail is designed to match the factory holes already present in the Rav4 passenger and driver side unibody structure. This allows you to mount these sliders to the Rav4 using all factory holes in the Rav4 unibody. No frame drilling, welding or modification required! (Although we do give the option of drilling 2 of the 10 holes to a slightly larger size for hard offroad use). With all of these design features in mind, you can rest assured that these sliders will hold up to whatever trail hits you can throw at them.\u003c\/p\u003e\u003cp\u003eThese rock sliders are then finished with a round tube outer rail and our signature tree logo step plates that provide a convenient step to get in and out of your Rav4 as well as access your roof rack or roof top tent. To make install easy, the sliders ship with clear and detailed step by step directions that are accompanied by tons of diagrams and pictures\u003c\/p\u003e\u003cp\u003e•NO WELDING REQUIRED – This rock slider set ships already welded and powdercoated in a durable black finish\u003c\/p\u003e\u003cp\u003e•NO Drilling, cutting or welding of the vehicle sheet metal required - (**option given to drill 2 of the 10 holes to a slightly larger size for hard offroad use)\u003c\/p\u003e\u003cp\u003e•Hardware Included\u003c\/p\u003e\u003cp\u003e•Detailed instructions and diagrams - the step by step directions and diagrams make for a clear and easy install\u003c\/p\u003e\u003cp\u003e•CNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access your roof rack or open your roof top tent\u003c\/p\u003e\u003cp\u003e•66.25\" slider length provide full wheel well to wheel well protection\u003c\/p\u003e\u003cp\u003e•3\/16\" steel inner rails are CNC cut and folded in-house and provide excellent foundational support - these are proper strong rock sliders!\u003c\/p\u003e\u003cp\u003e•Our unique design distributes forces evenly into your Rav4's unibody structure frame to prevent chassis damage\u003c\/p\u003e\u003cp\u003e•Hilift jack can be used anywhere along the slider length to lift the vehicle\u003c\/p\u003e\u003cp\u003e•45 degree tapered inner rails to glance off obstacles\u003c\/p\u003e\u003cp\u003e•Sold in pairs\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54289159323932,"sku":"CO13020","price":1205.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_228442c1-41ae-445e-9e1a-b5ef280dad62.jpg?v=1783585596"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/collections\/image_1920_228442c1-41ae-445e-9e1a-b5ef280dad62.jpg?v=1787062817","url":"https:\/\/shop-ca.dev-everfruitdigital.com\/collections\/rock-slider.oembed","provider":"Coastal Offroad","version":"1.0","type":"link"}